{"id":2723,"date":"2026-09-16T16:15:46","date_gmt":"2026-09-16T08:15:46","guid":{"rendered":"https:\/\/www.mold-mif.com\/?p=2723"},"modified":"2026-10-09T10:44:41","modified_gmt":"2026-10-09T02:44:41","slug":"auto-interior-assembly-part-injection-interior-accessory-with-connector-wire","status":"publish","type":"post","link":"https:\/\/www.mold-mif.com\/zh\/auto-interior-assembly-part-injection-interior-accessory-with-connector-wire\/","title":{"rendered":"Auto Interior Assembly Part, Injection Interior Accessory With Connector Wire"},"content":{"rendered":"

This assembly is the touch panel of a car door \u2014 the domed black housing a driver’s fingers find when pulling the door closed, with a bright plated trim ring around its base and a short harness ending in a two-way connector. It arrives as one wired unit: the housing, the trim ring, and the lead are mated before packing, so the line on the car side just plugs it in.<\/p>\n

The housing is injection molded in black with a gloss Class-A face; the trim ring is molded separately and plated. This page covers the visible surface, the wiring, the ribs inside the dome, and what we need confirmed before quoting.<\/p>\n

\"Car
The assembly: domed housing, plated trim, lead with connector.<\/figcaption><\/figure>\n

The Visible Surface<\/h2>\n

A gloss black interior part shows everything. Flow marks, blush at the gate, a faint sink over a rib \u2014 all of it reads under interior lighting, which in a car rakes across the panel from several angles at once. The dome is gated so the flow front reaches the crown evenly, the polish sequence on the cavity steel goes down to a diamond stage, and first articles are judged under a lamp at the angle a driver actually sees, not flat on a bench.<\/p>\n

The plated ring does more than decorate. It hides the joint between the housing and the door card, covering both the gap and the clip feet that hold the assembly in. Its plating is specified for interior service, and the housing underneath is a plating-grade grade of ABS \u2014 a resin choice made for the ring, not the dome.<\/p>\n

\"Front
Gloss dome and plated trim frame, seen from the front.<\/figcaption><\/figure>\n

The Wiring and the Connector<\/h2>\n

The harness is short on purpose. It runs from a lamp or switch inside the dome to a single connector a few centimetres away, where it meets the car’s door loom. The wire is routed through a channel moulded into the housing so it cannot sit between the assembly and the door card \u2014 a pinched wire behind trim is a warranty return that takes a dealer an hour to find.<\/p>\n

The connector end is fixed with a clip moulded into the housing, so the lead has no slack to rattle and the mating pull is taken by the housing, not the solder joint. Harness length, connector type and pin-out come from the customer; we mold the channel and clip around them.<\/p>\n

\"Rear
Rear view: ribs, routing channel and the connector clip.<\/figcaption><\/figure>\n

What the Ribs Carry<\/h2>\n

Behind the dome, ribs turn a shell into a structure. They carry the clip feet that snap the panel into the door, they brace the lamp pocket so the light does not shake, and they keep the dome from oil-canning when a hand presses it. The ribs stop short of the gloss face by a fraction of the wall \u2014 close enough to support it, far enough that they do not read as shadows through the surface. That standoff is one of the numbers we tune during sampling.<\/p>\n

The assembly also carries its identification on the back: a label with the part number and traceability code sits in a recess sized to it, flat and clear of the ribs, so it scans without peeling at an edge.<\/p>\n

\"Underside
The underside: clip feet and the recess for the ID label.<\/figcaption><\/figure>\n

Information to Confirm Before Starting a Car Interior Assembly Project<\/h2>\n
    \n
  • The door trim section drawing, which sets the clip feet and the joint the trim ring covers.<\/li>\n
  • Connector type, pin-out and harness length for the lead.<\/li>\n
  • What the assembly carries inside \u2014 switch, lamp or both \u2014 and its load.<\/li>\n
  • Colour and gloss target, plus whether the trim ring is plated or painted.<\/li>\n
  • Label content and the scan orientation the line requires.<\/li>\n<\/ul>\n

    Kunshan Maifeng Precision Industry Co., Ltd. molds and assembles interior parts like this one \u2014 housing, trim and harness mated and tested before packing \u2014 with all tooling built in house on machines from 90 to 700 tons. Send us the trim section and connector drawing, and we will come back with a structure proposal and a quotation.<\/p>\n

    \n

    Company Profile<\/h2>\n
    \n
    \"Kunshan<\/figure>\n
    \n

    About Us<\/h3>\n

    Kunshan Maifeng Precision Industry Co., Ltd. (MIF) has an investment of RMB 35 million and an independent factory of more than 5,000 m\u00b2. The company operates 36 single- and dual-color injection molding machines from 90 to 700 tons, together with more than 50 sets of mold manufacturing and processing equipment. Our service, management and production team includes over 100 people.<\/p>\n

    Our parent company was established in 2008. We provide product design, mold design and manufacturing, injection molding and product assembly services for custom plastic parts, supporting both domestic and international customers.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

    \n
    \n
    \n

    1. Product Design<\/strong>
    Product structure design and optimization based on customer drawings and samples.<\/p>\n

    2. Mold Design<\/strong>
    Mold design developed around product geometry, material and production requirements.<\/p>\n

    3. Mold Manufacturing<\/strong>
    Machining, polishing, fitting and assembly for custom injection molds.<\/p>\n

    4. Injection Molding<\/strong>
    Single- and dual-color injection molding for project and order requirements.<\/p>\n

    5. Product Assembly<\/strong>
    Supporting assembly services for molded plastic components.<\/p>\n<\/div>\n

    \"Maifeng<\/figure>\n<\/div>\n
    \n
    \"Maifeng
    Production Team<\/figcaption><\/figure>\n
    \"Maifeng
    Service Team<\/figcaption><\/figure>\n
    \"Maifeng
    Design Team<\/figcaption><\/figure>\n<\/div>\n<\/section>","protected":false},"excerpt":{"rendered":"

    A wired car door touch panel assembly: gloss black domed housing with a plated trim ring and a short harness to a two-way connector. Housing and trim molded in house, lead routed through a moulded channel. Built to your trim section and loom drawing.<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[141],"tags":[],"class_list":["post-2723","post","type-post","status-publish","format-standard","hentry","category-automotive-injection-molded-parts"],"_links":{"self":[{"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/posts\/2723","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/comments?post=2723"}],"version-history":[{"count":11,"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/posts\/2723\/revisions"}],"predecessor-version":[{"id":3657,"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/posts\/2723\/revisions\/3657"}],"wp:attachment":[{"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/media?parent=2723"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/categories?post=2723"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.mold-mif.com\/zh\/wp-json\/wp\/v2\/tags?post=2723"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}